Fisher & Paykel DD602I Instrukcja Użytkownika

DD602 (Prefinished) DD602I (Integrated)Models DD602 DD602IPart No. 599065/DUSA

Page DD_093.1.8Ensure there is a power outlet in reach of thesupplied flex. If there is not a suitable outletavailable then have one installed by aqua

Page DD_10The DishDrawer shouldnot support any part ofthe kitchen cabinets.WARNINGThe DishDrawer must belevelled so that eachcorner is at least within

Page DD_113.5.1Partially lift the top mounting tabs byinserting a flat screwdriver into the Veeshaped slot. Complete the foldingprocess by bending ab

Page DD_12 SECTION 4PREFINISHED TOE KICK INSTALLATIONSTEP 4.1 SETTING THE UPPER TOE KICK HEIGHT4.1.1Remove the Upper Toe Kick by openingthe bottom d

Page DD_13Ensure the Toe Kick Pinsare positioned on awooden chopping boardto avoid damage tosurrounding area.IMPORTANTSTEP 4.3 TRIMMING THE TOE KICK

Page DD_144.3.3If the height of the Lower Toe Kick isgreater than 11/4" (32mm) , insert the ToeKick Brace in between the two lowest ribsof the Lo

STEP 5.1 INTEGRATED DRAWER FRONT & TOE KICK DIMENSIONS5.1.1Use the following diagrams to work out the dimensions for the Integ

INTEGRATEDPRODUCTONLYIMPORTANTCheck top and bottommeasurements of cavityand use the smallerdimension to ensure thatthe drawer fronts and toekicks will

Accuracy is essentialwhen cutting the BadgeMounting Hole to ensurea neat fit to hold thebadge.IMPORTANTIMPORTANTAll marking out shouldbe done on the b

5.1.4Drawer Front Mounting Bracket Nut HolesUsing a 11/32 (8.5mm) diameter drill bit, drill out the four screw holes in each doorpanel to a depth of

Table of ContentsSection 1 General Information1.1 Preparation1.2 Product Specifications & Cavity Dimensions1.3 Options for Installing Multiple P

STEP 6.2 DISASSEMBLING THE INTEGRATED BADGE SECTION 6STEP 6.1 CHANGING THE INTEGRATED BADGE ENCLOSUREThere are several different colored Integrated

WARNINGCAUTIONTake care not to damagefront surface of panel.Ensure all cuts arestraight and care is takento avoid damage to theDrawer Front.Care shoul

INTEGRATEDPRODUCTONLYUse a small amount ofliquid soap along the lipof the seal to assist theDrawer Front to slide oneasily against the seal.The Electr

INTEGRATEDPRODUCTONLY DISHDRAWER TOE KICK INFORMATION SECTION 7Upper Toe Kick7.1.1Remove Plastic Toe Kick from product.Unscrew metal back panel.7.1.2

SECTION 8LEAVE ALL LITERATURE WITH THE CUSTOMER.Water underneath DishDrawer; check the hose connections and hose forleaks.Water around water supply

Electrical 110-120 VAC3 pin socket outletDrying Residual Heat& Fan AssistedWater Connection Recommended Hot140°F Max. (60°C)Water Pressure Maximum

Page DD_03Where the DishDraweris installed under acounter top, it isrecommended that barewood surrounding theDishDrawer is sealedwith an oil based pai

Page DD_04PLUMBING - DRAINAGE OPTIONSNote: Prefinished Model is shown. There is no variation in plumbing between Prefinished productsand Integrate

Page DD_05TOOLS NEEDED TOINSTALL DISHDRAWER Wooden Chopping Board Level Safety Glasses Utility Knife Pencil Drill & Drill Bits(3/32", 9

Page DD_06 SECTION 2FOOT SLIDE RETAINER INFORMATIONSTEP 2.1 ASSEMBLING THE FOOT SLIDE RETAINERIt is important that the FootSlide Retainer is c

2.1.5Position the Foot Slide Retainer within thecutout areas of the Template.2.1.6The Template should be placed in the cavityuntil the wings just touc

Page DD_083.1.1Feed the Power Cord, Inlet Hose andDrain Hoses through the Services Hole.Position the DishDrawer in front of theopening.3.1.2Connect th