Fisher & Paykel DD90SDF(H)TX2 Instrukcja Użytkownika

NZ AU GB IE590202B 12.11DD90SDF(H)TX2, DD90SDFTM2 (Designer) & DD90S(H)TI2 (Integrated) modelsINSTALLATION INSTRUCTIONSDishDrawerTM dishwas

107aCAVITY PREPARATIONWater ConnectionRecommended COLD (Maximum 60°C).¾ “ BSP (GB20) to suit flat washer.Water Pressure Water softener modelsMax. 1

117b7cINTEGRATED MODELS WITH REMOTE (NZ AU) ONLY - PREPARATION FOR EXTERNAL VENTING THROUGH SAME CABINETINTEGRATED MODELS WITH REMOTE (NZ AU) ONLY - P

128MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGELeft hand side Right hand side Drain hose - 2000 mmInlet hose - 1650 mmVenting hose - 1265 m

13

14RECOMMENDED METHOD (a) - SECURE WITHOUT DRAWER REMOVAL (FRAMELESS CABINETRY ONLY)10a9aATTACH SIDE MOUNTING BRACKETSINTEGRATED MODELS WITH REMOTE (NZ

1512a11aPULL THROUGH HOSES & MOVE INTO THE CAVITY SECURE THE DRAWER132Open the drawer halfway.Using a flat-bladedscrewdriver, prise the grey rubb

1610b9bINTEGRATED MODELS WITH REMOTE (NZ AU) ONLY - ATTACH VENTING HOSEPULL THROUGH HOSES & MOVE INTO THE CAVITYFitted ElbowCheck that the fitted

1711b 12b13b 14bREMOVE THE DRAWER SECURE THE DRAWER TO THE CABINETRYREFIT THE DRAWER ONTO THE RUNNERS INTEGRATED MODELS WITH REMOTE (NZ AU) ONLY - SEC

18INTEGRATED MODELS WITH REMOTE (NZ AU) ONLY - INSTALLING THE FRONT PANEL3112REMOVE BRACKET FROM PRODUCTATTACH PANEL TO PANEL BRACKET15a 16aImportant!

19INTEGRATED MODELS WITH REMOTE (NZ AU) ONLY - INSTALLING THE FRONT PANEL221Important!Ensure the rubber seal between the drawer and panel is kept in p

2FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR MODEL1DD90SDF(H)TX2DD90SDFTM2 DesignerPRODUCT & CABINETRYDIMENSIONSPARTS SUPPLIEDCAVITY PREPARA

20INTEGRATED MODELS WITH BADGE (GB IE) ONLY - INSTALLING THE FRONT PANEL & BADGE CONTROLSDETERMINE BADGE CUTOUT LOCATIONROUTE BADGE WIRING THROUGH

21REATTACH BADGE & EARTH THE PANEL ATTACH PANEL TO PRODUCT19b 20bWARNING!12Electrical Shock HazardConnect the integrated badge earth wire to one o

22ADJUST PANEL HEIGHT TO ALIGN THE CABINETRY GAPSInsert an appropriately sized Philips screwdriver into the hole above the door pin and rotate the pan

23THERE ARE TWO DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE.22132750-882.5 mm12 38 mmmax. 120 mm750-882.5 mm**3 45If spa

242625FINAL CHECKLIST TROUBLESHOOTINGCheck all parts are installed.Ensure product is level, securely fastened to the cabinetry and opens and closes fr

3ADDITIONAL SAFETY AND WARNINGS - INTEGRATED MODELS ONLY2b WARNING! Cut hazard Take care - panel edges are sharp. Failure to use caution could re

4PARTS SUPPLIED - ALL MODELS3aIf the Drain hose supplied is not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798

5ADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELS3bExternal Venting kit (1)supplied with Integrated models with remote (NZ AU) onlyPanel mounting scre

64PRODUCT DIMENSIONSAHIJKSidePlanGFBCDEProduct dimensions (mm)DesignerIntegratedRemotecontrolIntegratedBadge controlAoverall height1 of product (incl

75CABINETRY DIMENSIONSPlanSideLMPON18 mm20 mm2 mmONMinimum clearances from adjacent cabinetryCabinetry dimensions mmDesigner IntegratedRemotecontrolI

8The following calculations assume the top of the panel is aligned with the top of the adjacent cabinetry:WIDTH OF THE PANELMeasure A (the width betwe

9The following calculations assume the top of the panel is aligned with the top of the adjacent cabinetry:WIDTH OF THE PANELMeasure A (the width betwe