Fisher & Paykel DS602I Instrukcja Użytkownika

DS602I (Integrated)Models DS602 DS602IDS602 (Prefinished)Part No. 599066/DUSA

STEP 2.3 FLEXIBLE EXTRUSION ATTACHMENT FOR24 (610mm) CAVITYWiring, Plumbing andServices should becompleted beforeattaching the flexibleextrusion.TIP

SECTION 3DO NOT push againstthe middle of the drawer.The DishDrawer shouldnot support any part ofthe kitchen cabinetry.WARNINGMake sure the inlet an

Recommended DrawerFront thickness forIntegrated product is5/8" to 3/4" (16mm - 18mm).IMPORTANT SECTION 4INFORMATION FOR CABINET MAKER FORIN

A minimum clearance of3/32 (2.5mm) must bemaintained between theDrawer Front and existingcabinetry, exceptbetween the underside ofthe Drawer Front a

Accuracy is essentialwhen cutting the BadgeMounting Hole to ensurea neat fit to hold thebadge.IMPORTANTIMPORTANTAll marking out to bedone on the back

INTEGRATEDPRODUCTONLYUse of a depth gauge isrecommended whendrilling out holes forDrawer Front MountingPanel.WARNINGPage DS_144.1.5Drawer Front Mounti

SECTION 5STEP 5.1 CHANGING THE INTEGRATED BADGE ENCLOSURE INTEGRATED DRAWER FRONT INSTALLATIONSTEP 5.2 DISASSEMBLING THE INTEGRATED BADGE ASSEMBLY

WARNINGCAUTIONTake care not to damagefront surface of panel.Ensure all cuts arestraight and care is takento avoid damage to theDrawer Front.Care shoul

STEP 5.5 FITTING THE DRAWER FRONT TO THE DISHDRAWERUse a small amount ofliquid soap along the lipof the seal to aid theDrawer Front to slide oneasil

SECTION 6FINAL FITTING FOR SINGLE DISHDRAWER6.1.1Check final fit of DishDrawer in cavity.6.1.2Tighten M8 bolts.Page DS_18

Single DishDrawerTable of ContentsSection 1 General Information1.1 Preparation1.2 Product Specifications & Cavity Dimensions1.3 Options for Inst

SECTION 12FINAL CHECKSSTEP 7.1 INSTALLATION WET TEST SECTION 7STEP 7.2 TROUBLESHOOTINGWater underneath DishDrawer, check the hose connectionsand ho

Weight - Full 93lb (42kg) Prefinished - Empty 62lb (28kg) PrefinishedElectrical 110-120VAC3 pin socket outletDrying Residual Heat &Fa

Page DS_03Where the DishDrawer isin an under countersituation, i.e. built into akitchen unit, it isrecommended that barewood surrounding theDishDrawer

Note: DS602 Prefinished Model is shown. There is no variation inplumbing between DS602 Prefinished Model and DS602IIntegrated Model.Options 1 and 2 a

Page DS_05STEP 1.5 PRODUCT PARTSTools Needed ToInstall DishDrawer Wooden Chopping Board Level Safety Glasses Utility Knife Pencil Drill &

SECTION 2FITTING THE DISHDRAWEREnsure the cavity is atleast 227/8" (580mm) deep.TIPSTEP 2.1 DISHDRAWER MOUNTING HOLE LOCATIONS2.1.1Draw the ca

STEP 2.2 CONNECTING THE SERVICESEnsure the edges of theService Hole are smoothor covered. (See Step 1.2 -Product Specifications &Cavity Dimension

The Product MUST NOTbe plugged in at thisstage.WARNING2.2.6If required, trim the Single Connector tothe size which matches the waste tee or airbreak t