Fisher & Paykel DD36SDFTX2 Przewodnik Instalacji

Przeglądaj online lub pobierz Przewodnik Instalacji dla Zmywarki Fisher & Paykel DD36SDFTX2. Fisher & Paykel DD36SDFTX2 Installation Guide Instrukcja obsługi

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj
  • Strona
    / 20
  • Spis treści
  • BOOKMARKI
  • Oceniono. / 5. Na podstawie oceny klientów
Przeglądanie stron 0
US CA
590208D 04.13
DD36SDFTX2 (Designer) & DD36STI2 (Integrated) models
INSTALLATION INSTRUCTIONS
DishDrawer
TM
dishwasher
Przeglądanie stron 0
1 2 3 4 5 6 ... 19 20

Podsumowanie treści

Strona 1 - INSTALLATION INSTRUCTIONS

US CA590208D 04.13DD36SDFTX2 (Designer) & DD36STI2 (Integrated) modelsINSTALLATION INSTRUCTIONSDishDrawerTM dishwasher

Strona 2 - SAFETY AND WARNINGS

108MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGELeft hand side Right hand side Drain hose - 78 ½" (2000 mm)Inlet hose - 64 ¾" (165

Strona 4 - PRODUCT DIMENSIONS

12RECOMMENDED METHOD (a) - SECURE WITHOUT DRAWER REMOVAL (FRAMELESS CABINETRY ONLY)10a9aATTACH SIDE MOUNTING BRACKETSINTEGRATED ONLY - ATTACH VENTING

Strona 5 - CABINETRY DIMENSIONS

1311a 12aPULL THROUGH HOSES & MOVE INTO THE CAVITY SECURE THE DRAWERAs you push product in, pull through hoses and cord, ensuring they don’t get k

Strona 6 - - 2x

1410b9bINTEGRATED ONLY - ATTACH VENTING HOSE PULL THROUGH HOSES & MOVE INTO THE CAVITYFitted ElbowCheck that the fitted elbow is rotated left or r

Strona 7 - TERMINATE THE WIRING AS SHOWN

1511b 12b13b 14bREMOVE THE DRAWER SECURE THE DRAWER TO THE CABINETRYREFIT THE DRAWER ONTO THE RUNNERS INTEGRATED ONLY - SECURE THE EXTERNAL VENTBefore

Strona 8 - CAVITY PREPARATION

16221Important!Ensure the rubber seal between the drawer and panel is kept in place.REMOVE BRACKET FROM PRODUCTATTACH PANEL TO PRODUCTGROUND THE PANEL

Strona 9

17ADJUST PANEL HEIGHT TO ALIGN THE CABINETRY GAPS19Insert an appropriately sized Philips screwdriver into the hole above the door pin and rotate the p

Strona 10 - (excl. plug)

18THERE ARE THREE DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE.2013750-882.5 mm*21*21 38 mmmax. 120 mm750-882.5 mm*2*If s

Strona 11

19CONNECT INLET HOSE TO HOT WATER SWITCH PRODUCT ON21 2234Ensure the supplied rubber washer is fitted inside the coupling.Tighten coupling with wrench

Strona 12 - ATTACH SIDE MOUNTING BRACKETS

2ADDITIONAL SAFETY AND WARNINGS - INTEGRATED MODELS ONLY1b WARNING! Cut hazard Take care - panel edges are sharp. Failure to use caution could re

Strona 13 - Important!

2423FINAL CHECKLIST TROUBLESHOOTINGSpray armsCheck all parts are installed.Ensure product is level, securely fastened to the cabinetry and opens and c

Strona 14

3PARTS SUPPLIED - ALL MODELSADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELS2a2bExternal Venting kit (1) Panel mounting screws (14)Panel bracket (1)(a

Strona 15 - The product has three pairs

43PRODUCT DIMENSIONSAHIJKSidePlanGFBCDEProduct dimensions inches (mm)DesignerDD36SDFTX2IntegratedDD36STI2Aoverall height1 of product (incl. front pan

Strona 16 - ATTACH PANEL TO PANEL BRACKET

54CABINETRY DIMENSIONSPlanSideLMPNO⁄” (18 mm)⁄” (2 mm)⁄” (2 mm)NOMinimum clearances from adjacent cabinetryCabinetry dimensions inches (mm)

Strona 17

6The following calculations assume the top of the panel is aligned with the top of the adjacent cabinetry:WIDTH OF THE PANELMeasure A (the width betwe

Strona 18 - 750-882.5 mm

71819151617OPTIONALLY HARD WIRING PRIOR TO INSTALLATION91211111045677886a6c66bREMOVE THE DRAWERTERMINATE THE WIRING AS SHOWNREMOVE THE ACCESS COVER &a

Strona 19

87aCAVITY PREPARATIONImportant!Adjacent cabinetry must not extend above cavity baseMoisture protection tape must be applied.Services can be located ei

Strona 20

97b7cINTEGRATED MODELS ONLY - PREPARATION FOR EXTERNAL VENTING THROUGH SAME CABINETINTEGRATED MODELS ONLY - PREPARATION FOR EXTERNAL VENTING THROUGH A

Komentarze do niniejszej Instrukcji

Brak uwag